Note: For Spark 4D, navigate using SHIFT and the keypad (2, 4, 6, 8). 5 Press F5 Clear. The values in the connector cell and the slot cell are cleared. 6 In the connector cell, choose the output type.This documentation is delivered subject to the following conditions and restrictions: This document is protected by copyright and distributed under licenses restricting its use, copying, distribution and decompilation.
No part of this product or document may be reproduced in any form by any means without the prior express written authorization of Compulite Systems (2000) Ltd. The content of this document is furnished for informational use only and is subject to change without notice. Compulite Rave Driver To InstallCompulite Rave Patch Feature InstallingDocument version 2.0 February 2008 3 Table of contents About Compulite consoles and wysiwyg Work flow Requirements Installing wysiwyg and the Compulite driver To install wysiwyg To install the Compulite driver Configuring the PC to communicate with the console network To find the network ID on Vector To find the network ID on Dlite To find the network ID on 4D consoles and Sabre Connecting the console and the PC Connecting Vector Cabling Connection Connecting other consoles Cabling Connection Running wysiwyg Vector PC on the same PC with no LAN connection To enable communication with no LAN connection Transmitting virtual connectors (VC) To enable VC transmission for Vector To enable VC transmission for Dlite and Rave To enable VC transmission for Sabre and 4D consoles Establishing communication between the lighting console and wysiwyg To connect wysiwyg and the lighting console Enabling wysiwyg Input To patch and connect To use wysiwyg s Auto Patch feature Installing wysiwyg on a Vector console To install wysiwyg and Compulite driver on a Vector console 4 5 Connecting and Configuring Compulite Lighting Consoles and wysiwyg 1.0 About Compulite consoles and wysiwyg Pre-program a show with the Vector, Dlite, Rave, Sabre, and 4D consoles connected via Ethernet to a computer running Cast Software s wysiwyg. Link the console PC editions with wysiwyg s for visualizing cues. Compulite Rave Driver For WysiwygCompulite driver - Download the Compulite driver from: Downloads Visualizers Compulite Driver for wysiwyg. The driver s file name is: CompuliteWYSIWYGDriverSetup.exe. To install wysiwyg 1 Follow the instructions supplied by Cast Software. At the prompt Insert your console Manufacturer s Console Edition Drivers Disk, install the Compulite driver CompulitewysiwygDriverSetup.exe and run this file. When the installation is completed, you are prompted to insert the dongle and reboot the computer. After restart, run wysiwyg. ![]() Read the licence terms and click I Agree to continue. Select the type of dongle you are using. Compulite Configuring the PC to communicate with the console network SEPerformStandard Or CEConsoleConsole 4 After reading the information displayed, tap NEXT. This may take a few seconds. Tap FINISH. 3.0 Configuring the PC to communicate with the console network The computer running the wysiwyg software must be configured to the same subnet as the Compulite console. Example: If console IP is the PC LAN (local area network) must be configured manually to 90. Example: Network ID Console ID or 1 (for dual core and Vector Orange Note: For Dlite, Rave, Sabre, and the 4D consoles the PC IP address last byte can be any number. To find the network ID on Dlite Press SETUP SYSTEM OPTIONS IO ETHERNET. To find the network ID on 4D consoles and Sabre Go to menu 26. Connecting the console and the PC 4.0 Connecting the console and the PC Consoles are connected to the PC, running wysiwyg, via their Ethernet ports. The cabling used depends on whether the console is connected directly to the PC or is connected to the PC an Ethernet network. Wireless communication is also supported. Connecting Vector Use either the Data port or the Control port to connect to the PC running wysiwyg Cabling Connect from port Connect to Cable requirements Data PC Crossover cable Data Hub Standard cable Control Hub Crossover cable Control PC Standard cable Connection After connecting to the PC, whether directly or via a hub, there is no further requirement. Connecting other consoles Dlite, Rave, Sabre, and the 4D consoles all have one Ethernet port on their back panels. This port is used to connect between the console and the computer running wysiwyg. ATTENTION For Dlite, Rave, Sabre, and the 4D consoles Make sure that all the cables are connected before turning on the console. Reboot the console after verifying that the Ethernet port s green LED is on Cabling Connect Directly to PC Via hub Cable requirements Crossover cable Standard cable Connection After connecting to the PC, whether directly or via a hub, the Ethernet port s green LED is on. Running wysiwyg Vector PC on the same PC with no LAN connection If wysiwyg Vector PC are running on the same PC and the PC has no Ethernet connection then basically the LAN is not connected. In this case, wysiwyg Vector PC will not communicate with each other. Compulite Transmitting virtual connectors (VC) To enable communication with no LAN connection In the wysiwyg Device Manager, configure IP as This enables a loop back communication and connects the Vector PC and the wysiwyg. Transmitting virtual connectors (VC) Enable VC (virtual connector) transmission on the console s software. To enable VC transmission for Vector 1 Open the Tools menu. Tap Settings. 3 Open the Communication tab. Tap VIRTUAL CONNECTORS (VC S). When enabled, the background is light. Tap OK. The console automatically transmits all ports over the network. To enable VC transmission for Dlite and Rave 1 Press SETUP. Tap SYSTEM OPTIONS. Tap IO. 4 Tap ETHERNET. Tap ENABLE VC. When enabled, the background is dark. ![]() The console automatically transmits all ports over the network. To enable VC transmission for Sabre and 4D consoles On Sabre and the 4D consoles, you must determine which ports will transmit VC s and change the current VC table. Go to menu 26 - Network Settings. Press F5 VC Table. Press F5 Edit VC Table. Navigate to the relevant output cell for ID 000 using the arrow keys. Note: For Spark 4D, navigate using SHIFT and the keypad (2, 4, 6, 8). ![]() In the connector cell, choose the output type.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |